av大全在线-av大全在线观看-成人免费视-成人免费视频a-国产精品无-国产精品无码99re-黄色精品网站-黄色精品在线-久久久青青-久久久青青草-欧洲色网-欧洲色网站-男女爽爽视频-男女爽爽爽-日韩人成-日韩人妻精品一区二区三区

室內需要流通的空氣，在室內中安裝通風管道，確保通風暢通，同時在安裝過程中，要確保通風設備的防漏。因為一旦密封不好，整個工程所體現的效果也很一般。下面和山東通風管道廠家一起來了解下它的堵漏過程：

For indoor air that needs to be circulated, install ventilation pipes in the room to ensure smooth ventilation, and ensure the leak-proof of of ventilation equipment during installation. Because once the seal is not good, the effect of the whole project is also very general. Let's learn about the plugging process with Shandong ventilation pipe manufacturer:

1、清理：確定灌漿孔位置及間距。清理干凈需要施工的區域，清除表面析出物。

1. Cleaning: determine the location and spacing of grouting holes. Clean the area to be constructed and remove the surface precipitates.

2、埋嘴：觀察主漏水孔的壓力，水流不急壓力不大時可用快干堵漏劑埋注灌漿止水針頭。當結構達到一定的強度沒有滲漏時，其它泄水孔分別安裝膨脹止水針頭，用內六角扳手擰緊。墻面慢滲也依次安裝膨脹止水針頭。

2. Mouth burying: observe the pressure of the main leakage hole. When the water flow is not rapid and the pressure is not high, the quick-drying plugging agent can be used to bury the grouting water stop needle. When the structure reaches a certain strength and there is no leakage, other drain holes shall be installed with expansion water stop needles respectively and tightened with an Allen wrench. The expansion water stop needle shall also be installed in order for the slow seepage of the wall.

3、灌漿：使用高壓灌漿機試壓，向灌漿孔內灌注化學灌漿料。單孔逐一連續進行。當相鄰孔開始出漿后，保持壓力即可停止本孔灌漿。待所有的孔都灌完后，回到先前的灌漿孔，再次灌漿。

3. Grouting: use high-pressure grouting machine to test the pressure and inject chemical grouting material into the grouting hole. The single hole shall be carried out continuously one by one. When the adjacent holes begin to grout, the grouting of this hole can be stopped by maintaining the pressure. After all the holes have been filled, return to the previous grouting holes and grout again.

4、拆嘴：灌漿完畢，確認不漏，即可去掉或敲掉外露的灌漿嘴。清理灌漿液。

4. Nozzle removal: after grouting, the exposed grouting nozzle can be removed or knocked out after confirming that there is no leakage. Clean the grout.

5、補強：用密封劑對易滲漏部位進行封堵，用聚合物JS防水涂料。

5. Reinforcement: sealing agent is used to block the parts that are easy to leak, and polymer JS waterproof coating is used.

用鑿子或沖擊鉆將滲水部位打成4~5cm深，直徑2~3cm孔洞，用于沖洗干凈后，-1型材料加水（灰:水=1:0.3攪拌均勻，捏成料團手掌感覺發熱，迅速將料團塞于孔中，并用手掌壓住幾分鐘，手掌感到發硬后，松開手掌，再用木板壓平。15min后進行濕養護。

Use a chisel or impact drill to drill a hole with a depth of 4~5cm and a diameter of 2~3cm in the water seepage area. After washing, add water (ash: water=1:0.3) to the type - 1 material, mix it evenly, knead it into a ball, feel hot in the palm, quickly plug the ball into the hole, and press it with the palm for a few minutes. When the palm feels hard, loosen the palm, and then press it flat with the wood. After 15 minutes, wet curing is carried out.

涂層硬化后要進行濕養護注意事項：拌制材料隨用隨配，攪拌好料需要在凝結前用完；防水堵漏盡量避開烈日下施工，若在烈日下施工涂層凝固后，應及時加遮曬措施和濕養護，0?℃以下施工要添加防凍劑；資料貯存時，應置于室內干燥處。資料袋裝拆線后，余料應扎緊口，勿受潮。

Precautions for wet curing after the coating is hardened: the mixed materials shall be prepared as soon as they are used, and the mixed materials shall be used up before setting; Waterproof and leakage plugging shall be avoided as far as possible in the hot sun. If the coating is solidified in the hot sun, it shall be timely added with sunshade measures and wet curing? Antifreeze agent shall be added for construction below ℃; The data shall be stored indoors in a dry place. After the data bag is packed and stitched, the remaining material shall be tightly tied to prevent moisture.

關于通風工程的堵漏步驟小編就介紹這么多了，當然您記得定期檢查維護保養下通風管道，為了能夠更長久的更順利的使用，就要做到！更多相關內容就來我們網站http://www.159969.cn進行咨詢吧！

There are so many introductions about the plugging steps of the ventilation project. Of course, you should remember to check and maintain the ventilation pipes regularly. In order to use them more smoothly and for a longer time, we must do it! Come to our website for more relevant content http://www.159969.cn Consult!